Hard Facing

Nicromang deposit is a typical 13 - 16% manganese steel alloy with additions of chromium and nickel to improve its weldability and physical properties. It is primarily used for build up, repair, and joining of manganese steels.

Stoody 160 wire consists of tungsten carbide particles in a nickel silicon boron matrix. This microstructure gives Stoody 160 superior toughness, corrosion and excellent fine particle erosion resistance in slurry type applications.

Stoody 102 deposit has a composition and physical properties that are similar to those of H-12 tool steel. Weldability is very good and the wire can be applied out-of-position. Stoody 102 requires carbide tools for machining. It is good for hot wear applications up to 1100F.

A self-shielded cored wire which gives a Cr-Ni-Mo alloyed weld metal for rail surface repair.

Stoody 117 deposit consists of uniformly dispersed chromium carbides in a semi-austenitic matrix that provides a deposit with good impact, abrasion, and anti-galling properties. It develops a light crosschecking patter which allows this material to be applied in multiple layers without difficulty.

Stoody 100HC deposit is a high chromium-iron alloy recommended for application subject to severe abrasion and moderate impact and heat. It develops a very tight (3/8 - 1/2 inch) cross checking pattern and is frequently used in crushing applications. It is generally limited to two layers. In the rebuilding of coal pulverizer rolls, however, multiple layers can be applied using specific welding procedures. It can be applied using specific welding procedures. It can be applied to carbon, low alloy, and manganese steels.

Stoody 965-O is a general purpose hardfacing alloy offering a good balance of impact and abrasion resistance. Can be applied to carbon, low alloy and manganese steel. Applications would include both metal-to-metal and metal-to-earth.

Stoody 964 AP-G is a gas shielded flux cored general purpose hardfacing wire. Deposits from this all-position wire provide exceptional wear resisteance and high hardness. On Series 300 stainless and manganese steels, deposits are crack free. Other base metals should be preheated and post-heated appropriately. Stoody 964AP-G provides improved weldability over chromium carbide and many other tool steel welding wires. Use 964 AP-G where cross checking is undesirable.

Stoody 160 wire consists of tungsten carbide particles in a nickel silicon boron matrix. This microstructure gives Stoody 160 superior toughness, corrosion and excellent fine particle erosion resistance in slurry type applications.

Stoody 966-G is a molybdenum-tungsten high speed tool steel with a high concentration of uniformly distributed small primary carbides. The presence of the small carbides greatly improve the wear resistance when compared to M-7 tool steel. Stoody 966-G provides wear resistance greater than or equal to that of conventional chromium carbides but does not cross check when proper preheat and welding procedures are used. It is recommended for parts where cross checking is undesirable. It can be applied crack free without preheat on carbon, 300 series stainless and manganese steels. Preheat and interpass temperatures shall be determined by base metal requirements. Post weld heat treatment may be required for other base metals. The deposit will crack on cast irons.

Stoody CP-2000 is designed to produce a high concentration of uniformly distributed small primary chromium carbides in an austenitic matrix. The formulation is optimized for superior weldability in single and multiple layer applications. CP-2000 exhibits improved wear resistance and toughness over conventional chromium carbide alloys.

ThermaClad Multipass 1 is a low alloy steel composition build-up that exhibits an excellent combination of compressive strength and toughness. Deposits are machinable, crack-free, and can be flame cut. Maximum deposit thickness is unlimited.

A specially formulated chromium carbide alloy designed to produce a high concentration of uniformly distributed small primary carbides and secondary Niobium and Vanadium carbides in an austenitic matrix. CP-2001 has been optimized for superior single and multiple layer applications and can be applied to carbon, low alloy, and manganese steels - and even cast irons in coal pulverizer rebuilds.

Stoody 964-G deposit is a specially formulated wear resistant alloy which produces a uniform distribution of small primary carbides in a martensitic matrix. The small carbides provide greatly improved wear resistance over martensitic steel, many tool steels, and some conventional chromium carbide alloys. Stoody 964-G possesses excellent resistance to impact and plastic deformation. Deposits are crack free on carbon 300 stainless and manganese steels. Other base metals should be preheated and post heated appropriately. The material is characterized by a high hardness and excellent wear resistance and is recommended for parts where cross checking is undesirable. Stoody 964-G offers improved weldability over chromium carbide and many other tool steel welding wires.

Stoody 965-G is a general purpose hardfacing alloy offering a good balance of impact and abrasion resistance. Can be applied to carbon, low alloy and manganese steel. Applications would include both metal-to-metal and metal-to-earth.

Bare Acetylene Tube Borium is an oxy-fuel rod intended for metal-to-earth applications involving extreme abrasion and low impact. It is manufactured by metering crushed tungsten carbide particles of controlled mesh size into steel tubes.

A cored wire which produces a Cr-Mo-V-Co-W alloyed weld metal for hardfacing used with C1 shielding gas.

A general purpose hardfacing electrode depositing a semi corrosion resistant martensitic steel with a hardness of about 57 HRC. The electrode is specially suitable for hardfacing parts exposed to different forms of abrasive and impact wear, e.g. farming equipment, forestry tools, loading machines and mixers.

A cored wire which produces a work-hardening austenitic weld metal with high wear and impact resistance. Used with C1 shielding gas or self-shielded.

Stoody 155FC wire consists of tungsten carbide particles in a nickel silicon boron matrix. Designed for multiple pass operations where cross checking is undesirable. Stoody 155FC deposits are ideal when thicker nickel, silicon, boron tungsten carbide weld deposits are desired. Slightly reduced tungsten carbide produces greater ductility making Stoody 155FC a superior buffer layer for more wear resistant overlay alloys like Stoody 160FC.

Dynamang deposit is an austenitic manganese steel containing chromium and some nickel. It produces a tough, high-strength deposit that work hardens under impact. It is primarily used for the build up, repair, and joining of manganese steel components in the cement, rock-crushing and mining industries.

Stoody 101HWP is a chromium carbide alloy designed to generate primary carbides in the first layer. 101HWP exhibits superior wear in both single and double layer overlays in one or two layer wear plates. The alloy is optimized for superior weldability for weave and stringer bead deposits on plate.

Electrode giving a weld metal with coarse chromium carbides in an austenitic matrix. Suitable for surfacing worn parts in earth-moving equipment, sand pumps, mixers, feed screws, dust extractors, crushers etc exposed to wear by coal, ores and other minerals. Also in corrosive environment and/or elevated temperature.

Stoody HB-56 is a general purpose non-cracking hardbanding alloy that offer high hardness in a casing friendly deposit. HB-56 offers a balance of impact and abrasion resistance and can be applied to carbon and low alloy steels with or without tungsten carbide addition. Deposits are crack free when applied over new or properly rebuilt tool joints using appropriate preheats.

Stoody 134 deposit is a high chromium-iron alloy recommended for applications subject to severe abrasion, moderate impact, and high compressive loads. It can be deposited on carbon, low alloy, and manganese steel.

Stoody 160FC wire deposit consists of tungsten carbide particles in a nickel silicon boron matrix. Due to higher tungsten carbide content, Stoody 160FC is an ideal hardfacing overlay with a microstructure that delivers superior toughness and resistance to corrosion and fine particle erosion in slurry type applications. Stoody 160FC also provides improved weldability through enhanced wetting, tie-in, and arc stability.

A hardfacing cored wire for rebuilding and surfacing with C1 shielding gas.

OK 13Mn is an austenitic manganese steel electrode which work hardens under impact and compressive stresses. It is primarily used for surfacing and building up manganese steel components exposed to severe impact and moderate abrasion. Typical applications include crusher plates and rolls, cones and mantles of rotary crushers etc. The interpass temperature should be kept as low as possible.

Stoody M7-G deposit is a molybdenum high speed tool steel similar to AISI M7 grade.

A self-shielded cored wire which gives a Cr Mn alloyed weld metal for semi-automatic hardfacing.