Mild Steel

A general purpose metal cored wire for use with M21 or C1 shielding gas. Diameters less than 1.4mm are all-positional.

Basic thin coated AC/DC electrode providing excellent mechanical properties. The electrode ensures fully penetrated root passes even under adverse conditions. Low moisture content of the coating has a high resistance to moisture re-absorption. The electrode is CTOD-tested.

The non copper coated OK AristoRod 12.57 is a manganese-silicon bearing solid wire for welding of unalloyed steels, such as general structural, pressure vessel and ship building steels with a minimum tensile strength of 500 MPa, and for fine-grained carbon-manganese steels for the same purpose with a minimum yield strength of max 400 MPa. The electrode can be welded with Ar/20CO2 or with pure CO2 as the shielding gas. The wire electrode is suitable for welding at high currents.

Agglomerated fluoride-basic flux for Submerged Arc Welding. Primarily for multi-run welding. For highest demands on impact properties, low temperature toughness, strength and CTOD-values. Especially suitable for narrow gap welding due to good slag detachability and smooth side-wall blending. The Advanced Slag Release version improves weldability with excellent slag detachability, even better side wall wetting and stronger grains which improve weld quality due to flux grain size consistency also after multiple recycling cycles. All other attributes unchanged. For Offshore constructions, pressure vessels, power generation, shipbuilding, pipe mills, civil constructions, transport industries, etc. Produces weld metals with hydrogen contents maximum 5 ml/100 g, in BlockPac (moisture protection) maximum 4 ml/100g. Operates optimally at the lower end of the voltage range. Designed for single and multi wire procedures, for butt and fillet welds. Works equally well on DC and AC current. Single layer and multi layer welding of unlimited plate thickness.

A positional rutile cored wire for use with C1 or M21 shielding gas.

‍

Coreweld C6 was developed and "fine-tuned" especially for hand-held, automatic and robotic welding in the automotive industry, as well as rail car manufacturing, structural welding and other similar applications. Never before has there been such a perfect pairing of filler metal and industry requirements for quality, productivity and profitability.

A copper coated, G3Si1 solid wire for GMAW of all general structural and engineering unalloyed and low-alloyed carbon-manganese steels. Compared with OK Autrod 12.51, OK Autrod 12.56 has a slightly wider chemical analysis. The electrode may be welded with either a gas mixture or with pure CO2 as the shielding gas.

Agglomerated, aluminate-rutile, low basicity flux for Submerged Arc Welding. High welding speeds. Smooth weld beads and excellent slag detachability. For general construction, membrane wall panels, beam fabrications, automotive (wheels), etc. Primarily used with single- or twin-arc wire systems. For DC and AC. For single pass butt welds, overlap welds and fillet welds at high speeds.

A copper coated solid wire especially designed for downhill circumferential GMAW on pipes in materials such as APi 5L (grade 52 up to grade 70). The main applications are pipelines, compressor stations and associated works in the oil and gas distribution industries with special requirements. To meet these requirements the electrode is a "clean" type of EN ISO 14341-A G4Si1 as regards chemical analysis.

A metal cored wire for submerged arc welding.

A metal cored wire which gives a very low amount of silica on the weld surface. Designed for welding thin plate (>1mm) as well as thicker sections.with argon / carbon dioxide shielding gas. The wider welding arc produced means larger gaps can be bridged than with solid wire.

A downhand rutile cored wire for use with C1 or M21 shielding gas.

A basic cored wire for submerged arc welding.

A multi-purpose all positional rutile cored wire for use with C1 or M21 shielding gas.

OK 46.00 is an excellent performing, easy to use, rutile electrode and is relatively insensitive to rust or other surface impurities. It deposits smooth weld beads in all positions including vertical down with self releasing slag. Good striking and restriking properties making it ideal for short welds, root runs and tacking, also useful for bridging gaps.

This low hydrogen electrode is specially designed for downhill welding circumferential joints in pipes. The low hydrogen weld metal provides high notch toughness and excellent ductility to reduce the risk of cracking. The electrode is used particularly for pipelines, compressor stations, hot tapping and associated work using pipe steels in API 5LX52 to X70 grades in the oil and gas distribution industries, also process piping etc. Productivity is overall 25-30% faster than cellulosic electrodes and 40-50% faster than conventional low hydrogen electrodes for welding vertically up. Welding advice : Keep short arc using beaded or weaved runs. 2.5 mm size can also be welded uphill for increased heat input. DC- is preferred.

A copper coated, G4Si1/ER70S-6 solid wire for GMAW of general structural and engineering unalloyed and low-alloyed carbon-manganese steels. Compared with OK Autrod 12.51, OK Autrod 12.64 has a slightly higher silicon and manganese content, which increases the weld metal strength. The high silicon content promotes low sensitivity to surface impurities and contributes to smooth, sound welds. The electrode may be welded with either a gas mixture or with pure CO2 as the shielding gas. OK Autrod 12.64 can even be delivered in the unique Esab Octagonal Marathon Pac, which is an excellent choice in mechanised welding applications.

A metal cored wire for robotic or automated welding of single and multi-pass fillet welds using M21 and M12 shielding gas. Used in the downhand and horizontal / vertical positions.

A copper coated, G3Si1 solid wire for GMAW of all general structural and engineering unalloyed and low-alloyed carbon-manganese steels. The electrode may be welded with either a gas mixture or with pure CO2 as the shielding gas.

General purpose AC and DC+(-) basic electrode for mild and low alloy steels. The running characteristics are very good. It is a Low Moisture Absorption (LMA) type coating.

A basic cored wire for use with M21 or C1 shielding gas. Diameters less than 1.4mm are all-positional.

OK GoldRox is a true all-round and all-position rutile electrode. With exceptional arc stability and reduced spatter for decreased cleaning time, start and restart properties that allow for easy tack welds, and brilliant slag removal, novice and experienced welders can rely on OK GoldRox. Available in different package sizes – all fully recyclable – to make sure each pack fits specific job requirements.

Agglomerated fluoride-basic flux for Submerged Arc Welding. Designed for single-wire butt welding when high impact properties at low temperatures are required. For general construction, pressure vessels, power generation, transport industries, etc. Suitable for DC only. Single layer and multi layer welding of unlimited plate thickness.

A copper coated, G4Si1/ER70S-6 rod for GTAW of general structural and engineering unalloyed and low-alloyed carbon-manganese steels. Compared with OK Tigrod 12.61, OK Tigrod 12.64 has a slightly higher silicon and manganese content, which increases the weld metal strength. The high silicon content promotes low sensitivity to surface impurities and contributes to smooth, sound welds.

User friendly rutile electrode for steel construction and welding of sheet steel. Excellent bead appearance.

Agglomerated, aluminate-basic flux for Submerged Arc Welding. Very good surface finish and excellent slag detachability. Especially for concave horizontal fillet welds, as well for butt welds. High welding speeds. For general construction, beam fabrication, pressure vessels, pipe mills, transport industries, etc. Suitable for single and multi-wire procedures, for DC and AC. Due to the rather high Si-alloying intended for a limited number of passes and plate thickness up to about 25 mm.

Rutile coated electode designed for welding on flat position by the "contact" system on butt or filled joints; large amount of iron dust in coating, easy striking, high weld speed, beautiful finishing, high productivity.

Copper-coated, unalloyed wire for Submerged Arc and Electroslag Welding. Increased Si content and thus especially suitable for neutral fluxes (e.g.: OK Flux 10.62) or in order to increase the fluidity of the molten pool. With OK Flux 10.62 excellent toughness values; CTOD tested. For structural steels, ship building steels, pressure vessel steels, fine grained steels, off-shore constructions, etc.

A metal cored wire for robotic welding of single and multi-pass fillet welds using M21 and M12 shielding gas. Used in the down hand and horizontal / vertical positions.

Dual Shield II 711X is an all-position flux cored wire that displays exceptional impact properties in combination with CO2 shielding gas. This flux cored wire was developed to join low and medium carbon steels where higher impacts and toughness are required. As with all X Series wires, Dual Shield II 711X offers higher top-end current levels for out-of-position welding, broader operating ranges and higher deposition rates in out-of-position applications. ~Applications include construction, shipbuilding, rail car, light and heavy equipment, and general fabrication where exceptional impacts are required. Weld metal analysis is similar to Atom Arc 7018 and Atom Arc 7018-1.